Gshotts: /* Scan Manager */

2024-04-05T16:20:51Z

Scan Manager

← Older revision		Revision as of 11:20, 5 April 2024
Line 43:		Line 43:
	* Linear		* Linear
	* Tray		* Tray
	* Rotational		* Rotational (NDT Only)
	* Beam Profile		* Beam Profile
	* Megaboard		* Megaboard
Line 49:		Line 49:
	* Timed		* Timed

	In addition, Linear and Rotational scans can be complemented with complex [[Teach and Learn Setup\|Contour Following]] on two or more axes.		In addition, in ODIS-NDT, Linear and Rotational scans can be complemented with complex [[Teach and Learn Setup\|Contour Following]] on two or more axes.

	An Options page sets certain global scan options (trigger modes, disk caching, etc.		An Options page sets certain global scan options (trigger modes, disk caching, etc.

Gshotts: /* Using Advanced Mode */

2024-04-05T15:51:21Z

Using Advanced Mode

← Older revision		Revision as of 10:51, 5 April 2024
Line 8:		Line 8:
	In order to use Advanced Mode, either:		In order to use Advanced Mode, either:
	# The [[ODIS_Config.xml\|system configuration]] ''Mode'' key must be set to ''normal''. This will load the Basic Mode as the default unless the default login mode has been changed.		# The [[ODIS_Config.xml\|system configuration]] ''Mode'' key must be set to ''normal''. This will load the Basic Mode as the default unless the default login mode has been changed.
	# A use with the mode set to "Advanced" must login (See [[~~ODIS User Management#ODIS~~ Security Manager\|~~ODIS~~ Security Manager]]).		# A use with the mode set to "Advanced" must login (See the [[Security Manager\|Security Manager]]).

	==Advanced Mode Controls==		==Advanced Mode Controls==

Gshotts: Created page with "Category:Software Configuration Category:Run Modes Typical advanced Mode setup
Advanced Mode allows for complete control of all sub-sections of the ODIS software. It also has many more options for scanning, including Rotational scans, Contour Following, and Beam Profiles.
==Using Advanced Mode== In order to use Advanced Mode, either: # The ODIS_Config.xml|system config..."

2024-04-05T15:50:56Z

Created page with "Category:Software Configuration Category:Run Modes thumb|Typical advanced Mode setup Advanced Mode allows for complete control of all sub-sections of the ODIS software. It also has many more options for scanning, including Rotational scans, Contour Following, and Beam Profiles. ==Using Advanced Mode== In order to use Advanced Mode, either: # The ODIS_Config.xml|system config..."

New page

[[Category:Software Configuration]]
[[Category:Run Modes]]
[[File:AdvancedModeScreen.png|thumb|Typical advanced Mode setup]]

Advanced Mode allows for complete control of all sub-sections of the ODIS software. It also has many more options for scanning, including [[Rotational Scan|Rotational scans]], [[Teach and Learn Setup|Contour Following]], and Beam Profiles.

==Using Advanced Mode==
In order to use Advanced Mode, either:
# The [[ODIS_Config.xml|system configuration]] ''Mode'' key must be set to ''normal''. This will load the Basic Mode as the default unless the default login mode has been changed.
# A use with the mode set to "Advanced" must login (See [[ODIS User Management#ODIS Security Manager|ODIS Security Manager]]).

==Advanced Mode Controls==
In Advanced Mode, each subsection has a separate control form. To access controls, press the buttons on the left side of the screen. Some forms will be duplicated if there is more than one device (e.g. one Pulser/Receiver control form will appear for every detected digital Pulser/Receiver)

===Toolbar Buttons===
[[File:AdvancedModeButtons.PNG|thumb|50px|Control buttons]]
The buttons on the left side of the main window open and close the various control forms. If a control form is not available, pressing on the button will do nothing.

From top to bottom, the control buttons are:
* [[#Digital Oscilloscope|Digial Oscilloscope]]
* [[#Motion Control|Motion Control]]
* [[#Scan Manager|Scan Manager]]
* [[#Pulser Control|Pulser/Receiver Controls]]
* [[#Session Information|Session Information]]
* Point and Collect '''''(Note: this mode is obsolete and will be removed in a future release)'''''
* [[#Live Video|Live Video]]

 

===Digital Oscilloscope===
[[File:DigitalScope.png|thumb|Digital Oscilloscope]]
The [[Basic Controls|Digital Oscilloscope]] is identical to the setup found in [[Advanced Mode|Advanced mode]], with the exception that the A/D and Gates are set in the Instrument Tab on the main Setup window.
 

===Motion Control===
[[File:MotionWindowAdvanced.png|thumb|Motion Control Form]]
The motor control window is used to display position information and manually move axes. The system can be reinitialized and Home positions can be set as well.
 

===Scan Manager===
[[File:ScanManagerAdvanced.png|thumb|Scan Manager Form]]
The Scan Manager form contains the controls for configuration scans. The possible scan modes are:
* Linear
* Tray
* Rotational
* Beam Profile
* Megaboard
* Point
* Timed

In addition, Linear and Rotational scans can be complemented with complex [[Teach and Learn Setup|Contour Following]] on two or more axes.

An Options page sets certain global scan options (trigger modes, disk caching, etc.

 

===Pulser Control===
[[File:SamplePRWindowAdvanced.PNG|thumb|Typical Pulser/Reciever control form. Controls and settings will vary depending on the type of P/R.]]

More than one P/R form may appear if multiple pulser are present.

'''''Note:''' In Advanced Mode, a Pulser is '''Not''' turned on by default. The user must turn on the pulser before operating the system.''
 

===Session Information===
[[File:SessionInformationTestSetup.png|thumb|Session Information form.]]
 

===Live Video===
[[File:LiveVideo.png|thumb|Live Video display form.]]

Advanced Mode - Revision history

Gshotts: /* Scan Manager */

Gshotts: /* Using Advanced Mode */